Zestaw Open429I-C z STM32F429IGT6 Cortex-M4 - PACAGE S
Opis
Open429I-C zestaw rozwojowy z 32-bitowym mikrokontrolerem STM32F429IGT6 z rdzeniem ARM Cortex M4 oraz płyty bazowej. Moduła i otwarta konstrukcja czyni go idealnym układem do rozpoczęcia tworzenia aplikacji dla mikrokontrolerów z serii STM32. Open429I-C umożliwia rozbudowę o moduły peryferii firmy waveshare np. wyświetlacze LCD z panelem dotykowym (od 4.3" do 10,1") , moduły ethernet, dodatkową pamięć, transceiver CAN, RS485, kamery itp. rozbudowę ułatwiają dedykowane złącza.
- MCU core board connector: for easily connecting the Core429I
- USART3 interface: easily connects to RS232, RS485, USB TO 232, etc.
- DCMI interface: for connecting camera
- Capacitive touch panel interface: for connecting capacitive touch panel
- CAN2 interface: for connecting CAN modules
- CAN1 interface: for connecting CAN modules
- SDIO interface: for connecting Micro SD module, features much faster access speed rather than SPI
- ULPI interface: for connecting high-speed USB peripheral (the STM32F429I integrates USB HS controller without any PHY device)
- LCD interface 1: for connecting 7inch LCD
- ONE-WIRE interface: easily connects to ONE-WIRE devices (TO-92 package), such as temperature sensor (DS18B20), electronic registration number (DS2401), etc.
- LCD interface 2: for connecting 4.3inch LCD
- I2C2/I2C3 interface: easily connects to I2C peripherals such as I/O expander (PCF8574), EEPROM (AT24Cxx), etc.
- SAI1 interface: for connecting audio modules like UDA1380 module
- Ethernet interface: for connecting Ethernet modules
- USB connector: USB to UART via the onboard convertor PL2303
- SPI1/SPI2 interfaces:
- easily connects to SPI peripherals such as DataFlash (AT45DBxx), SD card, MP3 module, etc.
- easily connects to AD/DA modules (SPI1 features AD/DA alternative function)
- I2S2/I2S3/I2C1 interface: easily connects to I2S peripherals such as audio module, etc.
- 8-bit FMC interface: easily connects to peripherals such as NandFlash
- 5V DC jack
- 5V/3.3V power input/output: usually used as power output, also common-grounding with other user board
- MCU pins connector: all the MCU I/O ports are accessible on expansion connectors for further expansion
- PL2303: USB to UART convertor
- LEDs: convenient for indicating I/O status and/or program running state
- PL2303 TX-LED / RX-LED
- 12MHz crystal: for PL2303
- Joystick: five positions
- WAKE UP button: used as regular button, and/or wake up the STM32 MCU from sleep
- USB to UART jumper
- LED jumper
- short the jumper to connect to default I/Os used in example code
- open the jumper to connect to custom I/Os via jumper wires
- Button/Joystick jumper
- short the jumper to connect to default I/Os used in example code
- open the jumper to connect to custom I/Os via jumper wires
- STM32F429IGT6: the high performance STM32 MCU which features:
- Core: Cortex-M4 32-bit RISC
- Feature: single-cycle DSP instructions
- Operating Frequency: 180MHz, 225 DMIPS/1.25 DMIPS/MHz
- Operating Voltage: 1.8V-3.6V
- Package: LQFP176
- Memories: 1024kB Flash, 256+4kB SRAM
- MCU communication Interfaces:
- 6 x SPI, 4 x USART, 4 x UART, 2 x I2S, 1 x SAI, 3 x I2C
- 1 x FMC, 1 x SDIO, 2 x CAN
- 1 x LCD-TFT
- 1 x USB 2.0 HS/FS controller (with dedicated DMA)
- 1 x USB HS ULPI (external PHY required)
- 1 x 10/100 Ethernet MAC
- 1 x 8 to 14-bit camera interface
- AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)
- Debugging/Programming: supports JTAG/SWD interfaces, supports IAP
- IS42S16400J: SDRAM 1 Meg Bits x 16 Bits x 4 Banks (64-MBIT)
- AMS1117-3.3: 3.3V voltage regulator
- MIC2075: onboard USB power management device
- Power supply switch, powered from 5Vin or USB connection
- Boot mode selection, for configuring BOOT0 pin
- Power indicator
- VBUS LED
- Reset button
- 8M crystal
- 32.768K crystal, for internal RTC with calibration
- JTAG/SWD interface: for debugging/programming
- USB connector, supports Device and/or Host
- MCU pins expander, VCC, GND and all the I/O pins are accessible on expansion connectors for further expansion
- 5Vin pinheader, 5V power supply is required when using USB HOST/OTG
- USB OTG/HOST jumper
- short the jumper when using USB OTG/HOST
- open the jumper to disconnect from related I/O port
- VBAT selection jumper
- short the jumper to use system power supply
- open the jumper to connect the VBAT to external power, such as battery
- VREF selection jumper
- short the jumper to connect VREF+ to VCC
- open the jumper to connect VREF+ to other custom pin via jumper wire
W zestawie:
- Core429I + płyta bazowa
- Kabel mini USB
- Kabel mini USB gniazdo
- Przewody żeńsko - żeńskie (4szt.)
- Kabel zasilający z portu USB
Dodatkowe informacje: