Core429I STM32F429IGT6 Cortex-M4

Dostępność: brak towaru
Cena: 122,00 zł 122.00
ilość szt.

towar niedostępny

dodaj do przechowalni
Producent: WaveShare
Kod produktu: B3D2-26694

Opis

 

Moduł z 32-bitowym mikrokontrolerem STM32F429IGT6 z rdzeniem ARM Cortex M4 taktowany zegarem 180 MHz, 1024kb pamieci Flash oraz 256 kB SRAM. Na płytce znajduje się dodatkowa pamieć 64 Mb SRAM. jest to idealny układ aby rozpocząć pracy z STM32F4I.

 

  • Minimalny system umożliwiający pracę mikrokontrolera: system zegarowy, zasilanie USB, itp.
  • Pamieć: 64M Bit SDRAM
  • Wszystkie linie I/O dostępne na złączach goldpin
  • JTAG/SWD - interfejs programowania / debugowania
  • Raster złącz płytki: 2.0mm

  1. STM32F429IGT6: the high performance STM32 MCU which features:
    • Core: Cortex-M4 32-bit RISC
    • Feature: single-cycle DSP instructions
    • Operating Frequency: 180MHz, 225 DMIPS/1.25 DMIPS/MHz
    • Operating Voltage: 1.8V-3.6V
    • Package: LQFP176
    • Memories: 1024kB Flash, 256+4kB SRAM
    • MCU communication Interfaces:
      • 6 x SPI, 4 x USART, 4 x UART, 2 x I2S, 1 x SAI, 3 x I2C
      • 1 x FMC, 1 x SDIO, 2 x CAN
      • 1 x LCD-TFT
      • 1 x USB 2.0 HS/FS controller (with dedicated DMA)
      • 1 x USB HS ULPI (external PHY required)
      • 1 x 10/100 Ethernet MAC
      • 1 x 8 to 14-bit camera interface
    • AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)
    • Debugging/Programming: supports JTAG/SWD interfaces, supports IAP
  2. IS42S16400J: SDRAM 1 Meg Bits x 16 Bits x 4 Banks (64-MBIT)
  3. AMS1117-3.3: 3.3V voltage regulator
  4. MIC2075: onboard USB power management device
  5. Power supply switch, powered from 5Vin or USB connection
  6. Boot mode selection, for configuring BOOT0 pin
  7. Power indicator
  8. VBUS LED
  9. Reset button
  10. 8M crystal
  11. 32.768K crystal, for internal RTC with calibration
  12. JTAG/SWD interface: for debugging/programming
  13. USB connector, supports Device and/or Host
  14. MCU pins expander, VCC, GND and all the I/O pins are accessible on expansion connectors for further expansion
  15. 5Vin pinheader, 5V power supply is required when using USB HOST/OTG
  16. USB OTG/HOST jumper
    • short the jumper when using USB OTG/HOST
    • open the jumper to disconnect from related I/O port
  17. VBAT selection jumper
    • short the jumper to use system power supply
    • open the jumper to connect the VBAT to external power, such as battery
  18. VREF selection jumper
    • short the jumper to connect VREF+ to VCC
    • open the jumper to connect VREF+ to other custom pin via jumper wire

 

 

W zestawie: 

  1. Core429I x 1
  2. USB type A to Mini-B cable x 1
1    2

 

Dodatkowe informacje:

Wiki: www.waveshare.com/wiki/Core429I

Produkty powiązane

do góry
Sklep jest w trybie podglądu
Pokaż pełną wersję strony
Sklep internetowy Shoper.pl